rolec WALLPOD
A 7.4 kW smart charger with socketed and two tethered cable lengths.
UK specification · Last checked
Manufacturer specifications and support information, checked by EV Charger Megastore. We have not tested this charger hands-on. Our editorial standards.
rolec
WALLPOD
A 7.4 kW smart charger with socketed and two tethered cable lengths.
Before you choose
- Power and cable
- Up to 7.4 kW single-phase · Type 2 socket, 5 m tethered or 10 m tethered. Check the variant.
- Supply
- Single-phase terminals: 1P + N + E. Source
- Internet and controls
- Network: 4G LTE, Wi-Fi and Ethernet listed. Source
- Solar and home battery
- Solar: PV and storage integration dependent on app/back office. Source
- Installation requirements
- Load control: Dynamic load balancing; extra hardware may be needed. Source
- Energy tariff
- Check your car and charger with the energy supplier. Timed charging and supplier-controlled charging have different requirements. Understand tariff compatibility.
Read the full specification and exact model instructions before ordering. Hardware prices exclude installation unless the stated scope says otherwise.
On this page
Manufacturer part numbers
Match the full manufacturer part number (MPN), including its suffix, when comparing prices. A retailer's own stock code can be different. Confirm connectivity and hardware revision for the unit supplied.
| Variant | Manufacturer part number |
|---|---|
| 7.4 kW socketed grey | ROLEC4020G Source |
| 7.4 kW socketed white | ROLEC4020W Source |
| 7.4 kW socketed black | ROLEC4020B Source |
| 7.4 kW 5 m tethered grey | ROLEC4140G Source |
| 7.4 kW 5 m tethered white | ROLEC4140W Source |
| 7.4 kW 5 m tethered black | ROLEC4140B Source |
| 7.4 kW 10 m tethered grey | ROLEC4145G Source |
| 7.4 kW 10 m tethered white | ROLEC4145W Source |
| 7.4 kW 10 m tethered black | ROLEC4145B Source |
Electrical and charging specifications
| Specification | Detail |
|---|---|
| Output | Up to 7.4 kW, 32 A single-phase Source |
| Input | 230 V AC ±10%, 50/60 Hz Source |
| Mode | Mode 3 to IEC 61851-1 Source |
| Reduced supply | Unit downrates when the input supply is below maximum output Source |
| Single-phase terminals | 1P + N + E Source |
Connection and current codes
| Specification | Detail |
|---|---|
| Socketed codes | ROLEC4020G, ROLEC4020W, ROLEC4020B Source |
| 5 m tethered codes | ROLEC4140G, ROLEC4140W, ROLEC4140B Source |
| 10 m tethered codes | ROLEC4145G, ROLEC4145W, ROLEC4145B Source |
| Socketed connector | Universal Type 2 socket with cable lock Source |
| Tethered connector | Fixed Type 2 lead Source |
| Usable external cable | About 4.5 m on 5 m option; about 9.5 m on 10 m option Source |
Housing and environment
| Specification | Detail |
|---|---|
| Enclosure, W × H × D | 179 × 367 × 142 mm Source |
| Material | High-impact polycarbonate Source |
| Ingress | IP54 Source |
| Impact | IK10 Source |
| Status | Configurable RGB LED halo Source |
| Mounting | Wall or optional post Source |
Electrical protection and installation
| Specification | Detail |
|---|---|
| PME fault | Built-in; no earth rod required for this function Source |
| DC leakage | 6 mA DC fault detection built in Source |
| External AC protection | Sheet specifies suitably rated 30 mA Type A RCBO or equivalent at source Source |
| Over-current | Built-in protection listed Source |
| Temperature | Over-temperature protection and output derating Source |
| Surge | Surge protection may be needed depending on installation Source |
Connectivity and controls
| Specification | Detail |
|---|---|
| Access | App, RFID card or fob, or plug and go Source |
| Protocol | OCPP 1.6 Source |
| Network | 4G LTE, Wi-Fi and Ethernet listed Source |
| 4G subscription | Data subscription required Source |
| Meter | MID-approved energy meter Source |
| Solar | PV and storage integration dependent on app/back office Source |
| Load control | Dynamic load balancing; extra hardware may be needed Source |
Warranty and buying checks
| Specification | Detail |
|---|---|
| Maker warranty | Three years in current sheet Source |
| Colours | Grey, white and black charger codes Source |
| Accessories | Post, cards, fobs and vehicle leads are separate items Source |
| Price scope | No independently verified current exact-code supply-only price displayed Source |
Match the current code to the lead
Rolec’s current linked WALLPOD sheet maps nine charger codes to socketed, 5 m tethered and 10 m tethered versions in grey, white and black. The tethered lengths are total lead lengths; Rolec says the accessible cable beyond the unit is about 4.5 m or 9.5 m. The much longer code list at the bottom of its web page includes older and accessory identifiers, so this page uses the sheet’s mapped set. Rolec WALLPOD sheet; product page.
Check protection and services
The sheet calls for suitable 30 mA Type A protection at the source and lists built-in 6 mA DC detection and PME fault protection. It also notes that 4G needs a subscription, while dynamic load control and solar operation may need additional hardware or a compatible app. Confirm those items in the installation quote. Rolec WALLPOD sheet.
Price scope
No independent exact-code supply-only listing passed the live price check. Return to the Rolec range.
Manufacturer documents and sources
Specifications apply to the UK models identified above. Follow the instructions for the exact unit supplied; a product summary is not an installation manual.